Mode-S Beast:Lantronix Xport Software Setup: Difference between revisions

From Beast Wiki
Jump to navigation Jump to search
 
(6 intermediate revisions by the same user not shown)
Line 4: Line 4:


==Lantronix Device Installer==
==Lantronix Device Installer==
'''NOTE:''' Lantronix Device Installer does not work with Xport Edge


Lantronix Device Installer can be used to discover and check settings of the Xport<br>
Lantronix Device Installer can be used to discover and check settings of the Xport<br>
Line 15: Line 17:
This mode is used in order to directly transfer data from the Mode-S Beast over the network to Planeplotter.
This mode is used in order to directly transfer data from the Mode-S Beast over the network to Planeplotter.
For Xport use, it is quite essential to use the binary format, so DIP#3 must be ON.
For Xport use, it is quite essential to use the binary format, so DIP#3 must be ON.
===Xport Setup===


===Planeplotter Setup===
===Planeplotter Setup===
Line 23: Line 22:
[[File:Xport-udp-pp-setup.gif|Xport UDP Planeplotter Setup]]
[[File:Xport-udp-pp-setup.gif|Xport UDP Planeplotter Setup]]


====Xport Network Setup====
===Xport Network Setup===


[[File:Xport-network-settings.gif|700px|Xport Network Settings]]
Before doing any other work, you need to set the CPU Performance Mode to '''High''', press '''OK''' and then '''Apply Settings'''
 
[[File:Xport-server-settings.gif|700px|Xport Server Settings]]


''Important Note:''<br>While configuring, you always have to press "OK" button at the bottom, plus "Apply Settings" in the left hand menu.
====Xport Network Settings====


===Xport Server Settings===
'''Important Note:''' While configuring, you always have to press '''OK''' button at the bottom, plus '''Apply Settings''' in the left hand menu.


[[File:Xport-server-settings.gif|700px|Xport Server Settings]]
[[File:Xport-network-settings.gif|700px|Xport Network Settings]]


===Xport Connection Settings===
===Xport Connection Settings===
Line 38: Line 39:


===Xport Serial Settings===
===Xport Serial Settings===
Mind that here I was using 230400 baud rate, however 921800 is recommended.


[[File:Xport-serial-settings.gif|700px|Xport Serial Settings]]
[[File:Xport-serial-settings.gif|700px|Xport Serial Settings]]
The network load on a 100 MBit LAN is quite low, I was surprised that it was less than 1%.


==Setting up for TCP mode / COM port over Ethernet==
==Setting up for TCP mode / COM port over Ethernet==
Line 47: Line 48:
Newer versions of Planeplotter provide a direct TCP interface to the Xport, so data is not just streamed over the network but instead transmitted without loss and only if a device is connected.
Newer versions of Planeplotter provide a direct TCP interface to the Xport, so data is not just streamed over the network but instead transmitted without loss and only if a device is connected.


more to come (or on request)
===Xport TCP Settings Example===
 
[[File:Xport-tcp-settings1.png|640px|Xport TCP Settings (1)]]<p>
[[File:Xport-tcp-settings2.png|640px|Xport TCP Settings (2)]]<p>
 
 
 


You can also interface the TCP to the [http://www.lantronix.com/device-networking/utilities-tools/com-port-redirector.html Lantronix Com Port Redirector], which installs a COM port for the application side.
You can also interface the TCP to the [http://www.lantronix.com/device-networking/utilities-tools/com-port-redirector.html Lantronix Com Port Redirector], which installs a COM port for the application side.

Latest revision as of 10:27, 2 January 2020

Note that this setup currently needs to be updated to TCP mode! (All is equal but UDP no longer used as protocol)

Lantronix Device Installer

NOTE: Lantronix Device Installer does not work with Xport Edge

Lantronix Device Installer can be used to discover and check settings of the Xport
Note it might be that with some restricted LAN configuration (for example, NAT mode in a virtual machine running windows), these parameters won't show up completly.

Mode-S Beast - Lantronix Device Installer

Mode-S Beast - Lantronix Device Installer

Setting up for UDP mode

This mode is used in order to directly transfer data from the Mode-S Beast over the network to Planeplotter. For Xport use, it is quite essential to use the binary format, so DIP#3 must be ON.

Planeplotter Setup

Xport UDP Planeplotter Setup

Xport Network Setup

Before doing any other work, you need to set the CPU Performance Mode to High, press OK and then Apply Settings

Xport Server Settings

Xport Network Settings

Important Note: While configuring, you always have to press OK button at the bottom, plus Apply Settings in the left hand menu.

Xport Network Settings

Xport Connection Settings

Xport Connection Settings

Xport Serial Settings

Mind that here I was using 230400 baud rate, however 921800 is recommended.

Xport Serial Settings

Setting up for TCP mode / COM port over Ethernet

Newer versions of Planeplotter provide a direct TCP interface to the Xport, so data is not just streamed over the network but instead transmitted without loss and only if a device is connected.

Xport TCP Settings Example

Xport TCP Settings (1)

Xport TCP Settings (2)

You can also interface the TCP to the Lantronix Com Port Redirector, which installs a COM port for the application side.

Additional Hints

  • Factory reset without serial:
    Telnet to port 9999. Then you get a simple console menue, much like the BIOS setup of your PC. Simply do a factory reset, save and exit, and after a moment you will have it back on factory defaults.
  • Firmware upgrade of the Lantronix Xport:
    There is a FAQ of Lantronix, but ensure that the hardware revision of the Lantronix matches to that.