Mode-S Beast:Data Input Formats: Difference between revisions

From Beast Wiki
Jump to navigation Jump to search
imported>Dl4mea
No edit summary
 
(7 intermediate revisions by 2 users not shown)
Line 10: Line 10:


The next character sets or resets a DIP switch:
The next character sets or resets a DIP switch:
=== Mode-S Beast / Radarcape ===


{| class="wikitable"
{| class="wikitable"
|'''DIP'''
|'''DIP'''
|'''Bit'''
|'''Function'''
|'''Function'''
|'''OFF, open = lower case characters'''
|'''OFF, open = lower case characters'''
Line 18: Line 21:
|-
|-
|1,2
|1,2
| -
|Baudrate
|Baudrate
|not supported
|not supported
Line 23: Line 27:
|-
|-
|3
|3
|0
|Output Format AVR/Binary
|Output Format AVR/Binary
|"c"
|"c"
Line 28: Line 33:
|-
|-
|4
|4
|1
|DF-11/17 only filter
|DF-11/17 only filter
|"d"
|"d"
Line 33: Line 39:
|-
|-
|5
|5
|2
|MLAT info (AVR only)
|MLAT info (AVR only)
|"e"
|"e"
Line 38: Line 45:
|-
|-
|6
|6
|3
|CRC check disable
|CRC check disable
|"f"
|"f"
Line 43: Line 51:
|-
|-
|7
|7
|4
|'''Mode-S Beast classic:'''<br/>DF0/4/5 masking filter
|'''Mode-S Beast classic:'''<br/>DF0/4/5 masking filter
|"g"
|"g"
Line 48: Line 57:
|-
|-
|7
|7
|'''Radarcape:'''<br/>Legacy 12MHz Timestamp/<br>GPS Timestamp
|4
|'''Radarcape/Mode-S Beast GPS:'''<br/>Legacy 12MHz Timestamp/<br>GPS Timestamp
|"g"
|"g"
|"G"
|"G"
|-
|-
|8
|8
|5
|RTS handshake off/on
|RTS handshake off/on
|"h"
|"h"
Line 58: Line 69:
|-
|-
|9
|9
|6
|FEC disable yes/no
|FEC disable yes/no
|"i"
|"i"
Line 63: Line 75:
|-
|-
|10
|10
|7
|Mode-A/C enable on/off
|Mode-A/C enable on/off
|"j"
|"j"
|"J"
|"J"
|}
|}
=== Mode-S Beast Module ===
{| class="wikitable"
|'''Function'''
|'''OFF = lower case characters'''
|'''ON = upper case characters'''<br>'''[Default]'''
|-
|Output Format
|"c": AVR
|"C": Binary
|-
|DF-11/17 only filter
|"d": all known data formats
|"D": only DF-11 and DF-17
|-
|Timestamp info (AVR only)
|"e": ommitted
|"E": enabled
|-
|CRC check
|"f": enabled
|"F": disabled
|-
|Timestamp Resolution/<br>
|"g": Legacy 12MHz Timestamp
|"G": GPS Timestamp
|-
|Mode-A/C
|"j": off
|"J": on
|-
|User LED Red
|"r": off
|"R": on
|-
|User LED Yellow on/off
|"y": off
|"Y": on
|}
Mode-S Beast module
* always outputs GPS Timestamp "daysec" part in a range of 0..83999
* Requires RTS input on low TTL for outputting data.


'''Note:''' Months after the binary format was introduced, I got noticed that in ASCII <esc> is encoded as 0x1b. I actually wanted to use this code, but unfortunately only implemented my believes. For compatiblity reasons this will now stay as 0x1a and not be changed.
'''Note:''' Months after the binary format was introduced, I got noticed that in ASCII <esc> is encoded as 0x1b. I actually wanted to use this code, but unfortunately only implemented my believes. For compatiblity reasons this will now stay as 0x1a and not be changed.


'''Note:''' Setting 'g/G' is beeing used for GPS timestamp setting on the Radarcape
'''Note:''' Setting 'g/G' is beeing used for GPS timestamp setting on the Radarcape

Latest revision as of 19:40, 15 May 2020

The DIP switches are read during startup and taken as a default. Later they can be overwritten by software commands. Anyway, if then a DIP is changed to a position that is different to the pervious settings (by either hardware or software), the new setting takes account.

The software commands are the same in each output mode.

The input format is similar to the binary output format and allows control of DIP#3 until DIP#10 since baudrate setting does not make any sense over a serial interface. All commands start with a sequence

<esc> "1" <esc> is 0x1a, and "1" is 0x31

The next character sets or resets a DIP switch:

Mode-S Beast / Radarcape

DIP Bit Function OFF, open = lower case characters ON, closed = upper case characters
1,2 - Baudrate not supported not supported
3 0 Output Format AVR/Binary "c" "C"
4 1 DF-11/17 only filter "d" "D"
5 2 MLAT info (AVR only) "e" "E"
6 3 CRC check disable "f" "F"
7 4 Mode-S Beast classic:
DF0/4/5 masking filter
"g" "G"
7 4 Radarcape/Mode-S Beast GPS:
Legacy 12MHz Timestamp/
GPS Timestamp
"g" "G"
8 5 RTS handshake off/on "h" "H"
9 6 FEC disable yes/no "i" "I"
10 7 Mode-A/C enable on/off "j" "J"

Mode-S Beast Module

Function OFF = lower case characters ON = upper case characters
[Default]
Output Format "c": AVR "C": Binary
DF-11/17 only filter "d": all known data formats "D": only DF-11 and DF-17
Timestamp info (AVR only) "e": ommitted "E": enabled
CRC check "f": enabled "F": disabled
Timestamp Resolution/
"g": Legacy 12MHz Timestamp "G": GPS Timestamp
Mode-A/C "j": off "J": on
User LED Red "r": off "R": on
User LED Yellow on/off "y": off "Y": on

Mode-S Beast module

  • always outputs GPS Timestamp "daysec" part in a range of 0..83999
  • Requires RTS input on low TTL for outputting data.

Note: Months after the binary format was introduced, I got noticed that in ASCII <esc> is encoded as 0x1b. I actually wanted to use this code, but unfortunately only implemented my believes. For compatiblity reasons this will now stay as 0x1a and not be changed.

Note: Setting 'g/G' is beeing used for GPS timestamp setting on the Radarcape